How to set up a mixer how to#

If you flip them, they become very aggressive and pull bales apart. Razorback knives are reversible and act like Standard knives in their normal position. Adding knives or flaring knives out, makes the mixer more aggressive. Our basic mixer order starts with five Standard knives. Because of these options, knife combinations are nearly endless. Adding knives and setting knives out, increases horse-power requirements, so you may have limits to what you can process. Current mixers have ten possible knife locations and on nine of these, the knives can be set in or out. They are the Standard, Carbide tipped, Razorback and Lancer knives. Cloverdale TMR manufactures four different knives. These restrictors can be flipped upside down for smaller rations. However, if the restrictors are set too far in, the ration can be pushed up the side walls and spill out of the mixer. Generally, the further you set the restrictors in, the faster the ration will process. There are two restrictors, one located on the front left-hand side and one on the rear right-hand side of the mixer tub. Items that can affect feed processing are: Because used mixers can have worn plow wings, knives and auger flighting, we will assume that you are starting with a new mixer or one with new components. There are many factors that determine how well your Vertical TMR will process these bales.

How to set up a mixer how to#

Knowing how to set up your mixer for processing large round bales can get complicated. Large square bales and precut round bales can process much easier, because the bales fall apart as they process. Round bales of dry or wrapped material are usually the most difficult to process. The advantage of vertical TMR mixers over other designs is their ability to process long stem feed ingredients. Then the monitor loudspeakers wonвЂ™t sound too bassy and muddy.Setting up Your Mixer for Round Bale Hay Rations ThatвЂ™s where a graphic EQ can help: turn down frequencies a few dB below 200 Hz or so. The monitor signal from the board is generally pre-EQ, so turning down the bass (low frequencies) on the mic channel does not turn down the bass in the monitor loudspeakers. You also can use the graphic EQ to reduce the вЂњbassyвЂќ sound in the monitors caused by microphone proximity effect (the bass boost that occurs when directional mics are used up close). That EQ is used to reduce the levels of frequencies that feed back. ItвЂ™s also common to use a graphic EQ between the mixerвЂ™s monitor send (aux out) jack and the power amp that drives the monitor speakers. Try to get a flat spectrum (equal level in each frequency band) up to 1 kHz, then let the spectrum roll off gradually to about 10 dB down at 10 kHz.On the graphic equalizer, pull down the frequencies that are the highest on the RTA display.Play pink noise through one set of house loudspeakers (one combination of woofer, midrange and tweeter drivers).Plug the mic into a real-time analyzer (RTA) set to display 1/3-octave bands.Put the mic in the center of the audience area. Obtain a measurement microphone, which is an omnidirectional condenser mic with a flat frequency response.

HereвЂ™s another way to set a graphic equalizer: Adjust the graphic-EQ sliders to make the loudspeakers sound like the headphones in their bass-midrange-treble balance. One way to set a graphic EQ is to play some reference tracks alternately through high-quality headphones and through the house loudspeakers.

The graphic equalizer is used the flatten the frequency response of the house speakers and room so that the entire sound system is accurate or hi-fi. Mixer EQ affects the sound of each individual instrument and voice, while the graphic EQ affects the sound of the complete mix.

If you are recording a board mix of a service or show, connect the mixer REC OUT or TAPE OUT connectors to the recorder line inputs.Дў) Why would I put a graphic equalizer between the mixer and power amps? IsnвЂ™t that what the mixer EQ is for?.

If youвЂ™re not using a graphic equalizer for the house speakers, connect the mixer master outputs to the inputs of the power amp that drives the house speakers.

Connect the mixer master or main output to your graphic equalizer input, and connect the graphic output to your house power-amp input.

Connect each snake XLR connector to each mic input XLR connector.

Connect each mic to the stage box (snake).

Here we goвЂ¦ And note that all of the topics addressed in this article are illustrated in Figure 1 (below).ДЎ) What jacks should I use to connect the mixer to my sound system?